By Where is the throttle position sensor located?
butterfly spindle
A throttle position sensor (TPS) is a sensor used to monitor the air intake of an engine. The sensor is usually located on the butterfly spindle/shaft, so that it can directly monitor the position of the throttle.
Where is TPS located * throttle body engine throttle ECU?
TPS is usually located on the throttle valve spindle so that it can directly monitor its position. The TPS sensor is a potentiometer, providing a variable resistance depending on the position of the throttle valve (and hence throttle position sensor).
What are the signs of a bad throttle position sensor?
Symptoms of a Bad or Failing Throttle Position Sensor
- Car won’t accelerate, lacks power when accelerating, or accelerates itself.
- Engine won’t idle smoothly, idles too slowly, or stalls.
- Car accelerates, but won’t exceed a relatively low speed, or shift up.
Where is the throttle position sensor on a Polaris Ranger?
Throttle Position Sensor (TPS) – Located on the right-hand side of the throttle body below the IAC motor.
How do you reset throttle position sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How much does it cost to fix throttle position sensor?
The average cost for a Throttle Position Sensor Replacement is between $155 and $199 but can vary from car to car.
What should TPS be at idle?
At idle is should be zero or a couple of degrees. Press down on the gas pedal very S-L-O-W-L-Y until the throttle is all the way open. If the TPS has a worn spot, most likely it will be between 0 and 20 percent throttle opening. Try holding the throttle between 0 and 20 percent to see if you get a steady reading.
Can I unplug my TPS sensor?
If the TPS is not adjusted correctly as evidenced by a 500rpm idle, and hesitation with initial acceleration, unplugging the TPS connector should then cause a correct idle, and a normal acceleration. Correcting the TPS then produced a correct idle, and no code.
Is there a way to test a throttle position sensor?
Turn the key ON without starting the engine, ensuring the throttle is fully closed. If the digital multimeter reads between . 2 to 1.5 volts, then the throttle position sensor is working correctly. As you open the throttle plate, the digital multimeter should increase to 5 volts.
How do you test a Polaris TPS?
The only way to test the TPS is to use the tool Polaris designed to test it, or back-probe the yellow wire at the connector with a multi-meter and watch the voltage as you run up the throttle. It should climb smoothly, not erratically. Its hard to do as the numbers on the multi-meter run up quickly.
Can I clean my TPS sensor?
Cleaning the throttle body itself can be done using carburetor fluid and a clean cloth for the removal of light sludge. During this process, the throttle position sensor should not be cleaned due to the possibility of contamination or wire damage.
What kind of sensor does a Polaris RZR 4 use?
Fits for Polaris RZR 4 800 — 2010; RZR 800 EFI — 2008-2010; RZR 800 S — 2009-2010 Fits for Polaris Sportsman 700 EFI — 2007; Sportsman 800 EFI — 2007-2008, 2012-2014 Fits for Polaris Sportsman 800 Forest EFI — 2012-2014; Sportsman 800 HO — 2008 Fits for Polaris Sportsman 800 Touring — 2008-2009; Sportsman 850 XP EPS INTL — 2013
Is the Motoku throttle position sensor for Polaris Ranger 800 s?
I ordered this for a 2009 Polaris ranger rzr 800 s and it mounted up perfectly, but when I went to set the low idle adjustment voltage to .70v, It only went to .60v. There is no way you can use it that way because the ecu shoots a code and the machine runs horrible. Bought for my 2009 700 Ranger Crew.
Where is the TPS located on a Polaris?
Y ou c an find the original web page here: Side X Side World :: View topic – Polaris: TPS Adjustment 2010 and older The TPS is located on the passenger side of the throttle body. It tells the ECU how far open the butterfly in the throttle body is. If the TPS goes bad it can make the machine run erratically, or cause a hesitation at certain rpm’s.
How to adjust the TPS on a Ranger?
If you want to do it “right” and not pierce the wire insulation, you can buy the Polaris TPS adjustment harness ( Polaris part # 2201519-A ), which simply “T’s” into the existing harness plug. (2) Connect the negative lead of your meter to a good ground on the Ranger (the engine will work…..no need to go all the way to the battery).